Description
International Trilux 33 is a high performance, slow polishing antifouling, suitable for all types of hull construction, including
aluminium. Its bright colour makes it ideal for waterline boottops.
Formulated with Biolux Technology®, the slow polishing formula helps avoid paint build up and gives effective fouling protection for up to 18 months.Trilux 33 now has a lower VOC content that helps reduce environmental solvent emissions.
Features
- Biolux Technology for long-lasting antifouling protection
- Slow polishing formula suitable for use on aluminium craft, outdrives, outboards and any substrate
- Available in bright colours, including bright white
- Safe for use on aluminium
Specification
- Pack sizes: 375ml, 750ml & 2.5L
- Suitable for: Hulls, Propellers and Outdrives
- Finish/Sheen: Matt
- Type of Antifouling: Ablative
- Suitable Water Types: Sea Water, Fresh Water, Brackish Water
- Substrates: Aluminium / Zinc-Galvanised Steel, Epoxy Composite / Carbon Fibre, GRP/FRP, Lead, Steel, Wood, Bronze / Stainless Steel
- Application Method: Brush, Roller, Airless Spray
- Practical Coverage (Brush & Roller): 8.3 m²/L
- Practical Coverage (Spary): 3.66 m²/L
- Recommended Number of Coats (Brush & Roller): 3
- Recommended Number of Coats (Spary): 2
- Typical Shelf Life: 2 Years
Colour Avaliablity
- White
- Navy
- Black
- Red
- Blue
- Grey
- Green
Preparation
MAJOR REFURBISHMENT The first coat of Trilux 33 should always be applied over a recommended primer system. The primer surface should be dry and free of all contaminants (oil, grease, salt etc) and overcoated with Trilux 33 within the overcoating interval specified for the primer.
REPAIR and UPGRADING APPROVED SYSTEMS Degrease the surface. Clean the entire area with controlled high pressure washing (3000 psi./211 bar). Repair corroded areas with the recommended anticorrosive primer system (Primocon).
PRIMING All preparation for bare substrates is covered on the appropriate primer datasheet.
BARE GRP Gelshield 200 for osmosis protection, or Primocon.
STEEL/IRON Prime with Interprotect or Primocon.
LEAD Prime with Interprotect or Primocon.
WOOD Prime with Interprotect or Primocon.
ALUMINIUM/ALLOY Prime with Interprotect or Primocon.
Method
Ensure the area is clean and dry. Apply Trilux 33 within the overcoating intervals specified by the primer. Apply an extra stripe coat in areas of high wear such as chines, rudders, sterngear and any leading edges. Note: Maximum time to immersion is 6 months. If coating is left for more than 6 months, the surface should be high pressure fresh water washed or wet abraded using 180240 grade paper prior to immersion.
Hints
- Mixing: Stir well before use.
- Thinner: Thinner No.3
- Thinning: Thinning is not recommended. Use in exceptional circumstances only. For example, extremes of weather.
- Cleaner: Thinner No.3
- Airless Spray Pressure: 176210 bar. Tip Size: 2180. For Professional use ONLY.
- Other Take care to apply all the paint calculated even if it means applying an extra coat. It is important for performance to apply the correct thickness. It is important for performance to apply the correct thickness.
Hazard Warnings
Hazard Pictogram : | |
Signal Word: | Danger |
Hazard Statements: |
Flammable liquid and vapour |
Precautionary Statement: | General:
Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. Prevention:Wear protective gloves. Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use only outdoors or in a well-ventilated area. Avoid release to the environment. Response:IF INHALED: Remove person to fresh air and keep comfortable for breathing. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. IF ON SKIN: Take off contaminated clothing and wash it before reuse. IF IN EYES: Immediately call a POISON CENTER or physician. Storage:Keep cool. Disposal:Dispose of contents and container in accordance with all local, regional, national and international regulations. |
Hazardous Ingredients |
All Colours: Xylene, Rosin, Ethylbenzene, Pyrithione Zinc. |
Supplemental Label Elements |
Wear appropriate respirator when ventilation is inadequate. |