null
Ireland EU online store
International

International Cruiser 250 Antifoul - 750ml

€49.95
Frequently bought together:

Description

International Cruiser 250 is a self polishing antifoul, resulting in consistent antifouling performance while the boat is motion. Offers year-round protection, in all but the worst fouling areas. Suitable for all areas, freshwater and sea water use and most substrates. Use antifouling paints safely. Always read the label and product information before use.

Features

  • Offers a full year's protection
  • Protects against all kinds of fouling
  • Suitable for both powerboats and sailboats

Specification

  • Brand: International
  • Capacity: 750ml
  • Area: Below the waterline
  • Suitable for: Hull
  • Finish/Sheen: Matt
  • Substrates: Epoxy Composite, Carbon Fibre, Cast Iron, GRP/FRP, Lead, Steel, Wood
  • Application method: Brush, Roller
  • Recommended Number of Coats: 2 - 3
  • Practical Coverage (Roller & Brush): 9 m²/L
  • Type of Antifouling: Ablative
  • Suitable Water Types: Sea Water, Fresh Water, Brackish Water
  • Typical Shelf Life: 2 Years

Colour Availablity

  • Dover White
  • Blue
  • Navy
  • Red
  • Black

Preparation

PAINTED SURFACES

  • In Good Condition: All fouling and contamination must be thoroughly removed including the leached layer. Use high pressure fresh water wash (3000 psi/207 bar) and/or scraping and wet sanding with typically 80­120 grade paper. Do not dry sand. If old antifouling is incompatible or unknown, seal with suitable International Paint barrier/sealer coat.
  • In Poor Condition: Use Interstrip to remove all traces of antifouling.

PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet.

BARE GRP: Prime with Gelshield 200 for osmosis protection, or Primocon or Interprotect.

STEEL/IRON/LEAD/WOOD: Prime with Interprotect or Primocon.

PLYWOOD: Prime with Epiglass followed by Interprotect.

Hints

  • Mixing: Thoroughly stir until product is mixed to a uniform consistency before use.
  • Thinning: Thinning is not recommended. Antifouling performance can be compromised if correct dry film thickness is not applied.
  • Cleaner: YTA085 International Antifouling Thinner #3.
  • Ventilation and Humidity Control: Ensure adequate ventilation during use.
  • Other: Antifoulings should only be wet sanded. Never dry sand or burn­off old antifouling. True colour will develop after immersion.

Hazard Warnings

Hazard Pictogram :
Signal Word: Danger
Hazard Statements:

Flammable liquid and vapour
Causes serious eye damage
May cause an allergic skin reaction
Very toxic to aquatic life with long lasting effects

Precautionary Statements: General:

Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand.

Prevention:

Wear protective gloves. Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Avoid release to the environment.

Storage:

Keep cool.

Disposal:

Dispose of contents and container in accordance with all local, regional, national and international regulations.

Hazardous Ingredients

Dover White, Red, Blue, Navy, Black: : Dicopper oxide, Rosin, Fatty acids, C18-unsatd., trimers, compds. with oleylamine, Fatty acids, tall-oil, compds. with oleylamine

Supplemental Label Elements

Wear appropriate respirator when ventilation is inadequate.

Technical Files

Technical Data Sheet

Ireland Ireland Dover White - Safety Data Sheet

Ireland Ireland Red - Safety Data Sheet

Ireland Ireland Blue - Safety Data Sheet

Ireland Ireland Navy - Safety Data Sheet

Ireland Ireland Black - Safety Data Sheet

View AllClose