null
Ireland EU online store
International

International Gelshield Plus Epoxy Primer - Green - 2.25L

SKU:
85387-1
UPC:
8538711010101
€149.00
Frequently bought together:

Description

International Gelshield Plus is a high-build, solvent-free epoxy primer for the treatment of osmosis. It doesn’t contain any harmful solvents to ensure they don’t migrate into the hull and cause reblistering

Features

  • Contrasting colours (blue and green) to aid self-on-self application with wide overcoating flexibility
  • A high build, solvent-free epoxy primer for treatment of osmosis
  • At least 150 microns achieved per coat

Specification

  • Brand: International
  • Capacity: 2.25L
  • Area: Above & Below the Waterline
  • Suitable for: Hull
  • Finish/Sheen: Gloss
  • Substrates: GRP/FRP
  • Application Method: Brush, Roller
  • Recommended Number of Coats: 4
  • Practical Coverage: 6 m²/L
  • Typical Shelf Life: 2 Years

Colour Avaliablity

  • Green

Preparation

OSMOSIS TREATMENT: Gelcoat should be removed by blasting, or by peeling plus a light blasting. The resultant substrate should be carefully examined and professionally evaluated as chemically dry. Surface must be clean and dry prior to application of Epiglass HT9000 or Gelshield Plus. Contact International for further details.

Method

OSMOSIS TREATMENT: Apply initial coat with a thin foam roller and work into the surface using a brush. (Alternatively, Epiglass can be used as the first coat in the scheme). Lay off with a brush making sure a minimum of 150 microns wet film thickness is applied (Minimum 150 micron wet film thickness is not essential when Epiglass is used as the first coat in the scheme). Fill as required using, Interfill 830, Interfill 833 or Watertite. At temperatures of 10­15°C it is recommended that the fast cure versions of Interfill 830 and Interfill 833 are used. If filler "set" to an extent that the surface does not move under light pressure, then overcoating can proceed. Otherwise, the filler should be sanded prior to application of Gelshield Plus. Apply a further 3 coats of Gelshield Plus by roller, each coat at least 150 microns. At shorter overcoating intervals, a "wet on tacky" application technique can be employed. As soon as Gelshield Plus is firm enough it can be overcoated with itself, even if the surface is still tacky.

Hints

Mixing: Stir contents of each part prior to mixing. Mix the base and curing agents of Gelshield Plus together at the specified mix ratio. Stir well before use. Pour immediately into a wide flat tray to prevent premature curing. 

Thinning: Do not thin under any circumstances.
Cleaner: Epoxy Thinners No. 7 for equipment cleaning only. Ensure equipment is cleaned before product has gelled.
Other: If self­on­self overcoating times are exceeded, abrade surface thoroughly to remove gloss. The minimum overcoating times given are guidelines only. In some instances, depending on curing conditions, substrate temperature etc, the next coat may be applied faster than this. If the final coat overcoating times are exceeded, abrade with 80 grade paper before application of Gelshield 200. If cold, and before mixing, store Gelshield Plus at room temperature for 12
hours or stand in containers of warm water to warm product up to approximately 15°C. Excessive warming will severely reduce pot life. When applying by roller, laying off with a brush will aid release of any surface air. If the laminate requires re­building Epiglass resin should be used. Do not use Gelshield Plus for any laminating work. Before antifouling can be
applied a tie coat of Gelshield 200 is needed.

Hazard Warnings

Hazard Pictogram :
Signal Word: Warning
Hazard Statements:

Causes serious eye irritation
Causes skin irritation
May cause an allergic skin reaction
Toxic to aquatic life with long lasting effects

Precautionary Statement: General:

Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand.

Prevention:

Wear protective gloves. Wear eye or face protection. Avoid release to the environment. Avoid breathing vapour. Wash hands thoroughly after handling. Contaminated work clothing should not be allowed out of the workplace.

Response:

Collect spillage. IF ON SKIN: Wash with plenty of soap and water. Take off contaminated clothing and wash it before reuse. If skin irritation or rash occurs: Get medical attention. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention.

Storage:

Not applicable

Disposal:

Dispose of contents and container in accordance with all local, regional, national and international regulations.

Hazardous Ingredients

Grey: Phenol, Polymer with Formaldehyde, Glycidyl Ether, Reaction Product: Bisphenol-A- (epichlorhydrin); Epoxy Resin.

Supplemental Label Elements

Wear appropriate respirator when ventilation is inadequate.

Technical Files

Technical Data Sheet

Ireland Ireland Green Part A- Safety Data Sheet

Ireland Ireland Green Part B - Safety Data Sheet

View AllClose