Laser Deck Fittings: Cleats, Bungs & Bailers

The Laser Pico Mainsheet Padeye 91303 is the official deck fitting made in stainless steel from Laser Boats. Dimensions Width 35mm Length 40mm Height 25mm Fasteners: 4 x 5mm countersunk Material: S/S

Description Laser XD Deck Plate Stainless Steel Features Deck plate to attach the outhaul and cunningham blocks Stainless steel

Grabrails for ILCS and Laser Sailboats - Colour Grey - Suits all Rigs

ILCA Laser Centreboard Stop Set by Holt How to assemble Allign the first cap fitting to the centre shaft and push down hard to until the shaft is flush with outer side of cap  Fit the part assembled unit to the centreboard and then align and...

ILCA deck mounted fairlead for traveller system. Fits ILCA 7,6 & 4 and Laser standard, radial & 4.7.

Specifications Aluminium Hard anodised Inside diameter: 6mm Fixing hole size: 4mm Fixing spacing: 23mm Weight: 12g

RWO R2067 screw-in black drain bung, suit fitting R2066 - Popular fit to many dinghies including Laser and ILCA Dimensions Aperture 17mm

RWO 2064 bayonet style white drain replacement bung for R2060 Dimensions Aperture 17mm Cut out 22mm

The ILCA Laser XD Stainless Steel Block Plate is deck mounted to guide the Downhaul and Outhaul Control lines towards the Harken Deck Jam Cleat . The plate is mounted directly aft of the mast slot and includes 2 x Laser XD Harken 16 mm Air...

Nautos Autobailer to suit all model Laser and ILCA sailing dinghies, comes as a complete swop-out assembly with fixing scrww

ILCA Laser Painter Line in yellow flecked, floating polyproplene line - 8mm x 8m Braid - Satisfies the requirement to carry a tow line in ILCA Class Events

RWO screw-in black drain bung and socket - Suits Laser and many other sailing dinghies Dimensions Aperture 17mm Cut out 22mm

Laser Cockpit Drain 92184 - This Laser Drain Bush Set sits at the rear of the cockpit and creates the opening for the self-bailer control rod to operate through. When replacing this item, be sure to bed it with Sikaflex 291    

Harken ball bearing cam cleats hold lines securely and release instantly for easy, precise trimming. Aluminum Cam-Matics are hardcoat-anodized for high-load, high-wear, continuous adjustment applications. Replaces ILCA Laser LS-91517 used for ILCA Laser...

These bailer spring plates are manufactured using the highest quality spring stainless steel, designed to both retract using spring tension, and at the same time providing a surface for the activator to push against to close the chute. NOTE: This...

Optiparts Drain Plug for Laser.

The aluminium ball bearing Laser cam cleat is features hard anodized and PTFE coated ball bearing cams. Aluminium cams for Laser sailling wear significantly less than carbon composite (plastic) cams. Specifications Material: Aluminium Fixing screw: 5 mm...

The ILCA Laser rudder retaining clip prevents the rudder popping up and becoming detached. The rudder clip is easy to fit but remember to use Sikaflex or similiar sealant to keep the hull watertight.

Laser Toe Strap Padded in grey with XD logo. Internal plastic stiffener stops the Laser Toe Strap from turning over, heat sealed screw holes for easy fit.

Holt Laser Grab Rail fit all Laser Performance and ILCA Dinghies  - Two required per boat - It is recommended to use a sealant, such as Sikaflex 291i to bed screws  Accessories Sikaflex 291i Sealant - Click here  

Official ILCA approved Nautos self-bailer ( Autobailer)  - Suits all models ILCA and Laser

Standard Bow eye fairlead for all Laser and ILCA rig sail boats

ILCA Laser Centreboard or Daggerboard Stops - These push-together sets prevent the Daggerboard dropping too low  How to assemble Allign the first cap fitting to the centre shaft and push down hard to until the shaft is flush with outer side of...

The MK1 flat back rubber friction pad for the deck of any Laser dinghy designed as a friction plate to keep the Laser daggerboard in place during sailing.

The ILCA Laser XD Stainless Steel Block Plate is deck mounted to guide the Downhaul and Outhaul Control lines towards the Harken Deck Jam Cleat . The plate is mounted directly aft of the mast slot and requires 2 x Laser XD Harken 16 mm Air Block...

ILCA Harken XD Outhaul & Downhaul Deck Ceat with Harken Double Jammer. Suits all models ILCA & Laser - Official branded ILCA product. Fasteners 2x A4 Stainless 10 x 1 1/2" self tappers Use sealant in when installing.

RWO deck mounted, traveller fairlead with stainless steel insert Suits ILCA 4,6 & 7 and Laser 4.7, Radial & Standard. Features 10mm Aperture Hole centres 23mm Height 18mm High load bearing,acetal resin with stainless insert