Laser Deck Fittings: Cleats, Bungs & Bailers

The Laser Pico Mainsheet Padeye 91303 is the official deck fitting made in stainless steel from Laser Boats. Dimensions Width: 35mm Length: 40mm Height: 25mm Fasteners: 4 x 5mm countersunk Material: S/S

Laser XD Deck Plate Stainless Steel Features Deck plate to attach the outhaul and Cunningham blocks Stainless steel

Grabrails for ILCS and Laser Sailboats - Colour Grey - Suits all Rigs

ILCA Laser Centreboard Stop Set by Holt How to assemble Align the first cap fitting to the centre shaft and push down hard to until the shaft is flush with outer side of cap  Fit the part assembled unit to the centreboard and then align and...

ILCA deck mounted fairlead for traveller system. Fits ILCA 7,6 & 4 and Laser standard, radial & 4.7.

Holt Laser Replacement Aluminium Fairlead Boom & Deck (Pair) : HT.282ALU Holt arts are high quality replacements that perform the same function as the original part. They should not be confused with official parts bearing the Laser® registered...

RWO R2067 screw-in black drain bung, suit fitting R2066 - Popular fit to many dinghies, including Laser and ILCA Dimensions Aperture: 17mm Weight: 5 g  

The ILCA Laser XD Stainless Steel Block Plate is deck mounted to guide the Downhaul and Outhaul Control lines towards the Harken Deck Jam Cleat. The plate is mounted directly aft of the mast slot and includes 2 x Laser XD Harken 16 mm Air Blocks...

Nautos Autobailer to suit all model Laser and ILCA sailing dinghies, comes as a complete swop-out assembly with fixing screw Features Slide down chute with 'O rings' Screw and plastic insert included Drains water from cockpit Easy retrofits to older...

ILCA Laser Painter Line in yellow flecked, floating polypropylene line - 8mm x 8m Braid - Satisfies the requirement to carry a tow line in ILCA Class Events.

RWO screw-in black drain bung and socket - Suits Laser and many other sailing dinghies. Specifications Fixing center distance (mm): 36 Fixing (mm): 4.0 Weight (g): 11 Cutting (mm): 22.0 Dimensions Aperture 17mm Cut out 22mm

Heavy grade Eye Strap with 32mm Hole Centres - Used for hiking strap, stern bulkhead attachment on ILCA Laser.

Laser Cockpit Drain 92184 - This Laser Drain Bush Set sits at the rear of the cockpit and creates the opening for the self-bailer control rod to operate through. When replacing this item, be sure to bed it with Sikaflex 291. The drain bushing assembly...

Harken ball bearing cam cleats hold lines securely and release instantly for easy, precise trimming. Aluminum Cam-Matics are hardcoat-anodized for high-load, high-wear, continuous adjustment applications. Replaces ILCA Laser LS-91517 used for ILCA Laser...

These bailer spring plates are manufactured using the highest quality spring stainless steel, designed to both retract using spring tension, and at the same time providing a surface for the activator to push against to close the chute. NOTE: This...

Rooster toestraps use a unique rubber compound that has a very high coefficient of friction, whilst also being light and durable. Our new Pro Plus Range has this rubber added to the bottom of our padded toestrap. Rooster Pro Plus Padded straps are super...

Optiparts Drain Plug for Laser.

The aluminium ball bearing Laser cam cleat is features hard anodized and PTFE coated ball bearing cams. Aluminium cams for Laser sailling wear significantly less than carbon composite (plastic) cams. Specifications Material: Aluminium Fixing screw: 5 mm...

The ILCA Laser rudder retaining clip prevents the rudder popping up and becoming detached. The rudder clip is easy to fit but remember to use Sikaflex or similar sealant to keep the hull watertight. Features Will secure the rudder to the transom You can...

The Pico Toe Strap plate is used to spread the load when attaching toe strap or MK1/MK2 Laser friction pad. Specifications Material: Plastic Colour: Blue

Laser Toe Strap Padded in grey with XD logo. Internal plastic stiffener stops the Laser Toe Strap from turning over, heat sealed screw holes for easy fit. Features XD toe strap for maximum grip and control Loop will fit shockcord and toe strap...

The ILCA Laser Grab Rail Grommets are for attaching the Laser Grab Rail. The Grab Rail requires five per side. Grommets are supplied in a pack of ten which will complete one ILCA Laser Hull. Remember to put Sikaflex on before you attached the Grab Rail...

Holt Laser Grab Rail fits all Laser Performance and ILCA Dinghies - Two required per boat - It is recommended to use a sealant, such as Sikaflex 291i, to bed screws  Accessories Sikaflex 291i Sealant - Click here  

Official ILCA approved Nautos self-bailer ( Autobailer) - Suits all models ILCA and Laser. Complete autobailer assembly for the ILCA dinghy with bailer plate, chute door, bung, and screw. This is a class legal bailer with ILCA stamp on body of the bailer...

Standard&nbsp Bow eye fairlead for all Laser and ILCA rig sail boats   Acetal open-based and bullseye rope fairleads with or without stainless steel liner. Features Fixing Hole Size: 5mm Dist. Between Fixing: 5mm Weight: 30g

Aluminium deck cleat is designed to hold 12mm to 16mm rope under high pressure. Specification Material: Aluminium Rope diameter: 1/2 - 5/8" (12 mm - 16 mm) Hole diameter: 3 3/4" (95 mm) Length: 4 5/8" (118 mm) Width: 1 1/2" (37 mm) Height: 1 3/4"...

The Laser Harken Cammetrick cleat is similar to the Laser Cleat 91517, but this one is made of plastic. Harken Micro Cam Cleats hold lines securely and release instantly for easy, precise trimming. Lightweight fiber-reinforced Carbo-Cams for racing where...

ILCA Laser Centreboard or Daggerboard Stops - These push-together sets prevent the Daggerboard dropping too low. How to assemble Align the first cap fitting to the centre shaft and push down hard to until the shaft is flush with outer side of...

The MK1 flat back rubber friction pad for the deck of any Laser dinghy designed as a friction plate to keep the Laser daggerboard in place during sailing.

The ILCA Laser XD Stainless Steel Block Plate is deck mounted to guide the Downhaul and Outhaul Control lines towards the Harken Deck Jam Cleat. The plate is mounted directly aft of the mast slot and requires 2 x Laser XD Harken 16 mm Air Block with Fork...

ILCA Harken XD Outhaul & Downhaul Deck Cleat with Harken Double Jammer. Suits all models ILCA & Laser - Official branded ILCA product. Fasteners 2x A4 Stainless 10 x 1 1/2" self tappers Use sealant in when installing

A replacement bung for your Laser Self Bailer. Very easy to fit and recommended to have a spare Bailer Bung with your sailing kit. Laser® is a registered trademark owned by Velum Limited and currently licensed for use in Europe to Laser...

RWO deck mounted, traveller fairlead with stainless steel insert. Suits ILCA 4,6 & 7 and Laser 4.7, Radial & Standard. Features 10mm Aperture Hole centres 23mm Height 18mm High load bearing, acetal resin with stainless insert