Laser Rudders and Centreboards

Complete package of Laser® and ILCA® protection for maststep, mast, tiller, outhaul and daggerboard. Contains 2 disks for the maststep, 2 stripes for the maststep and mast deck, 2 stripes for snug fit of the top mast section, 1 stripe for the...

ILCA Laser Centreboard Stop Set by Holt How to assemble Allign the first cap fitting to the centre shaft and push down hard to until the shaft is flush with outer side of cap  Fit the part assembled unit to the centreboard and then align and...

Holt Marine Pre Packs - Monel Metal Pop Rivets Monel is is resistant to corrosion and acids so will not rust Ideal for fixing fittings on masts and booms A rivet gun will be required for fixing rivets

ILCA or Laser tiller retaining pin to secure the tiller to the rudder head, supplied with securing cord Note If your tiller is not drilled to receive the retaining pin, ensure the tiller is firmly pressed into the head before drilling the location hole...

A rudder ring is a must if you would like to keep your Rudder. It provides a secondary attachment of the rudder to the hull preventing detachment. Make sure you have a rudder ring fitted to save you money in the future.

The Inexpensive, clear hard plastic profiles which fit over the traling edge of the Laser daggerboard and rudder. Protects your Laser foils from damage in storage or transportation. Specifications Material: Plastic Colour: Clear

The ILCA Laser rudder retaining clip prevents the rudder popping up and becoming detached. The rudder clip is easy to fit but remember to use Sikaflex or similiar sealant to keep the hull watertight.

ILCA Laser Centreboard or Daggerboard Stops - These push-together sets prevent the Daggerboard dropping too low  How to assemble Allign the first cap fitting to the centre shaft and push down hard to until the shaft is flush with outer side of...

The ILCA Laser Friction Pad MK2 is screwed to the back of your daggerboard casing and allows for perfect grip and slip ratio when raising the board.

The MK1 flat back rubber friction pad for the deck of any Laser dinghy designed as a friction plate to keep the Laser daggerboard in place during sailing.

Laser Rudders Gudgeons by Holt - 2 Required per boat  Fasteners 2 x Sowester Pan Head Self Tappers per Gudgeon - Size  8 x 1 1/2"  Select size here

Genuine ILCA Rudder Gudgeon asteners 4 x Sowester Pan Head Self Tappers per Gudgeon - Size  8 x 1 1/2"  Select size here

This ILCA / Laser tiller retaining pin secures the tiller to the rudder head. Note If your tiller is not drilled to receive the retaining pin, ensure the tiller is firmlypressed into the head before drilling the location hole to ensure solid fit

Official ILCA Rudder Head comes with rudder megabolt.  Suits all models ILCA 4, 6 & 7 and Laser 4.7, Radial and Full Rig

The Laser rudder head is a aluminium construction complete with a rudder ring and tilller retaining pin. Rudder fittings are stainless steal for long lasting, please make sure you rudder head has the approve sticker for eventing. Comes with rudder...

High quality, reliable RWO OmniflexTiller Joint to suit most dinghy tiller extension, including ILCA Laser, Topper, and many others. This Omniflex joint is made from Elastomeric polymer which allows all directional flexability. The fitting includes a...

The ILCA Mega Bolt is the pivot bolt to fit the Rudder Head to the Rudders Plade - Supplied with 20mm Washers 

The Laser XD rudder head pivot bolt is an upgraded large diameter bolt and nylock nut with 20 mm washers. The rudder bolt will hold your rudder blade firmly in place.

Official ILCA fused rudder blade only - Suiys all models and Class leagal for all ILCA events. Note Also suits Laser (Torch logo) Sailboats.