Laser Rudders and Centreboards
-
Optiparts ILCA/ Laser Protection Pack
Optiparts
TDD444.51Complete package of Laser® and ILCA® protection for maststep, mast, tiller, outhaul and daggerboard. Contains 2 disks for the maststep, 2 stripes for the maststep and mast deck, 2 stripes for snug fit of the top mast section, 1 stripe for the...OPEX2001TDD444.51 -
ILCA Laser Centreboard ( Daggerboard) Stop Set by Holt
ILCA
TDD94.44ILCA Laser Centreboard Stop Set by Holt How to assemble Allign the first cap fitting to the centre shaft and push down hard to until the shaft is flush with outer side of cap Fit the part assembled unit to the centreboard and then align and...HT70201TDD94.44 -
Holt Monel Metal Rivets 1/4X1/2 (3 Pack)
Holt
TDD72.57Holt Marine Pre Packs - Monel Metal Pop Rivets Monel is is resistant to corrosion and acids so will not rust Ideal for fixing fittings on masts and booms A rivet gun will be required for fixing rivetsHA389TDD72.57 -
Holt Laser Rudder Retaining Pin with Cord 70141
Holt
TDD50.69ILCA or Laser tiller retaining pin to secure the tiller to the rudder head, supplied with securing cord Note If your tiller is not drilled to receive the retaining pin, ensure the tiller is firmly pressed into the head before drilling the location hole...HT70141TDD50.69 -
Laser All Boats Rudder Clip Ring
Laser
TDD6.93A rudder ring is a must if you would like to keep your Rudder. It provides a secondary attachment of the rudder to the hull preventing detachment. Make sure you have a rudder ring fitted to save you money in the future.LS-85314TDD6.93 -
Optiparts Foil Protector Set for Laser - Clear
Optiparts
TDD72.57The Inexpensive, clear hard plastic profiles which fit over the traling edge of the Laser daggerboard and rudder. Protects your Laser foils from damage in storage or transportation. Specifications Material: Plastic Colour: ClearOPEX2059TDD72.57 -
ILCA / Laser Rudder Retaining Clip
ILCA
TDD36.10The ILCA Laser rudder retaining clip prevents the rudder popping up and becoming detached. The rudder clip is easy to fit but remember to use Sikaflex or similiar sealant to keep the hull watertight.ILC5954TDD36.10 -
ILCA Laser Daggerboard Stop Sets
ILCA
TDD72.57ILCA Laser Centreboard or Daggerboard Stops - These push-together sets prevent the Daggerboard dropping too low How to assemble Allign the first cap fitting to the centre shaft and push down hard to until the shaft is flush with outer side of...ILC3916TDD72.57 -
ILCA Laser Friction Pad - MK2
ILCA
TDD123.62The ILCA Laser Friction Pad MK2 is screwed to the back of your daggerboard casing and allows for perfect grip and slip ratio when raising the board.LS-91538TDD123.62 -
Laser Performance Friction Pad - MK1
Laser
TDD152.79The MK1 flat back rubber friction pad for the deck of any Laser dinghy designed as a friction plate to keep the Laser daggerboard in place during sailing.LS-85239TDD152.79 -
Holt Laser Rudder Gudgeon - Suits all Rigs
Holt
TDD43.39Laser Rudders Gudgeons by Holt - 2 Required per boat Fasteners 2 x Sowester Pan Head Self Tappers per Gudgeon - Size 8 x 1 1/2" Select size hereHT911201TDD43.39 -
ILCA Laser Rudder Gudgeon
ILCA
TDD50.69Genuine ILCA Rudder Gudgeon asteners 4 x Sowester Pan Head Self Tappers per Gudgeon - Size 8 x 1 1/2" Select size hereILC5950TDD50.69